Smart column on the switch controller
Smart column on the switch controller

Smart column on the switch controller

Downloaddownload

Specifications

Smart column on the switch controller

◆ Overview:

Smart column switch controller is a high-speed sampling chip and 32-bit high-speed processor combined with a new high-voltage switch controller, can quickly and steadily complete the high-voltage switch monitoring. It combines protection, monitoring, control, communication and other functions in one, with high integration, flexible configuration, friendly interface and so on. Widely used in 6-35kv transmission and distribution power supply system, can help the system to identify the line transient fault and permanent failure, can automatically eliminate the impact of instantaneous failure on the line, but also isolated permanent fault section, to avoid long-term large area power outage , Automatic recovery of non-fault section of the grid power supply, thus economical and practical to achieve distribution network automation.
(GSM / GPRS / CDMA), Ethernet, WIFI, optical, power carrier, RS232 / 485, RJ45 and other means of communication, and access to other station equipment (such as TTU, FTU, DTU, etc.), support DNP3, IEC60870- 101,104, Modbus protocol.

◆Use the environment

1. Ambient air temperature: -40 ℃ ~ +55 ℃, daily temperature difference: Daily change: 25 ℃;

2. Elevation: not more than 4000 meters;

3. Wind speed: no more than 35m / s;

4. No frequent severe vibration;

5. No strong corrosive gas, medium places (such as various acids, alkali, smoke, etc.);

6. Put pollution capacity level IV;

7. Storage temperature: -40 ℃ ~ +55 ℃.

◆ product application

Widely used in 6-35kv transmission and distribution power supply system, the controller with the switch with the identification of instantaneous fault and permanent fault line, automatic isolation of permanent fault segment.

Suitable for the occasion: the column on the border switch control, the column load switch control, column user boundary load switch control, column segment switch control, contact switch control.

◆ Border switch controller (watchdog controller)

The controller is the monitoring unit of the medium voltage overhead line power grid. The on-board switch is used to realize the automatic monitoring of the line state, the fault analysis and the judgment record, and has the functions of driving the switch protection line equipment safety, cutting the line fault and automatically resuming the line operation. Applicable to 35kv and below outdoor switch equipment include: vacuum circuit breakers, oil circuit breakers and gas circuit breakers.

The controller is suitable for spring operating mechanism vacuum circuit breaker, set line protection, control, voltage, current signal measurement, monitoring in one integrated automation outdoor monitoring and control device. It has all the functions of handling all voltage and current signals of one overhead line and one remote switch.

◆ function

1. With a quick break, limited time off, set the time limit overcurrent of the three-stage protection;

2. With hand-assisted acceleration section protection function, the circuit breaker in the fault to accelerate the trip, and closed closing;

3. With 0 to 4 times the automatic closing function, to meet the “sub-t1-sub-t2-sub-t3-sub-t3-points – lock” work characteristics, with coincidence acceleration, coincidence times, coincidence Delay can be set freely;

4. With zero sequence protection, can determine the small current to ground fault;

5. With inrush suppression protection function

6. With over-voltage trip protection

7. With loss of pressure protection function

8. With the power to close the protection function

9. With frequency protection function

10. With energy storage alarm function

11. Event records

12. Real-time clock

13. Real-time status query

Optional features

1.SOG function 2. Dual PT function 3.CT anti-open function 4. Smartphone control

◆ technical parameters

Power Supply Rated power supply AC 220V
Nominal voltage tolerance -20% ~+20%
Power waste ≤ 5W
Rated frequency 5Hz
Waveform distortion ≤ 5%
Rating Current transformer 5A or1A,Power waste< 1.0VA/ mutually
Voltage transformer 220V,Power waste< 0.5VA/ mutually
frequency 50Hz
Measuring range and precision Protective current 0.10~99.99A ≤ ±3.0%
Zero sequence current 0.010~9.999A ≤ ±0.5%
Voltage 0.1~280.0V ≤ ±0.5%
Protective performance parameter Event resolution 2ms
Quick exit time stay1.2In under,Group action time≤ 40ms
Export time difference ≤ 1%
Exit relay Contact load (resistance) 10A/220VAC,10A/28VDC
Electrical life 10 Million times
Electromagnetic compatibility insulation resistance ≥ 10M
Insulation strength 2.5kV,1min
Voltage dips and voltage interruptions 100%,0.5s
High frequency interference mode 1.5kVP,1min
common mode 2.5kVP,1min
transients 4.0kVP,1min
Wave interference 4.0kVP,1.2/50μs
Electrostatic discharge 8kV
Power frequency magnetic field 100A/m
Damped oscillatory magnetic field 100A/m
impulse voltage 5kV,1.2/50μs
All EMC and performance indicators meet the DL/T 721-2000IV standard
communication interface The main port 1 way RS85 excuse (baud rate optional)
work environment Operating temperature -25% ~+70%
Storage temperature -40% ~+70%
humidity 5% ~100%Including gel
Environmental temperature change rate 25℃ /h
atmospheric pressure 70~106KPa
surrounding environment No explosion, corrosive gas and conductive dust, no bacteria, no violent vibration
Impact source
Other technical indicators Overall weight ≤ 5kg
Shell protection class ≥ IP65
Mean time between failures ≥ 50.00h

◆Permanent magnet switch controller

The controller is the monitoring unit of the medium voltage overhead line power grid. It cooperates with the on-board switch to realize the automatic monitoring of the line state, the fault analysis and the judgment record, and has the functions of driving the switch protection line equipment safety, cutting the line fault and automatically resuming the line operation. Applicable to 35kv and below Switchgear equipment include: vacuum circuit breakers, oil shorters.

The controller is suitable for permanent magnet operation mechanism vacuum circuit breaker, set line protection, control, voltage, current signal measurement, monitoring in one integrated automation outdoor monitoring and control device. It has all the functions of handling all voltage and current signals of one overhead line and one remote switch.

◆Current – time type splitter controller

The controller is a digital overcurrent-pulse type segment controller with the number of times the memory pre-stage switch (recloser or circuit breaker) disconnects the fault current and cuts the line from the grid after a predetermined number of interrupts. Widely used in the distribution (domain network, rural network), it is 6kv or 10kv overhead lines on the column vacuum circuit breakers, load switches and other equipment to control the operation, in other equipment with the realization of distribution network fault location , Fault isolation and automatic fast recovery of non-faulty areas of power supply.

◆ function

1. Overcurrent detection 2. Ground (zero sequence) protection

3. Inrush current protection 4. Loss of pressure detection

5. Event log 6. Real-time clock

7. Real-time status query 8. Smartphone control (add as needed)

◆ Features

1. Interval fault current setting can be set 2. Zero sequence fault setting can be set

3. Inrush time can be set 4. The number of memories can be set

5. Low voltage delay alarm 6. With anti-jump function

Product Reviews

There are no reviews yet. Be the first one to write one.

Write A Review

Resources

For more Other high-voltage products.
please contact a sales representative at sale16@gotoelectrical.com or submit a Quote Request.

    A trusted electrical supplier

    A firm commitment to providing excellent quality products, services and experiences that meet the needs of all our customers.

    Enquire Now

    Stay connected with Industry Insights

    Stay informed with news and insights that matter to you and get quarterly updates sent direct to your inbox.

    Contact Us
    Smart column on the switch controller